Enphase Relay controller, 1-phase, 20A

Enphase
Q-RELAY-1P-INT
4 In stock
ENERGY : Solar PV Balance Of System
Meet the Q Relay behind smart energy. In Enphase IQ installations, the multiphase Q Relay acts as a grid monitoring and disconnection device and includes a built-in phase coupler to distribute power line communication signals across phases. An external phase coupler is not needed when the Q Relay is installed....

Meet the Q Relay behind smart energy.

In Enphase IQ installations, the multiphase Q Relay acts as a grid monitoring and disconnection device and includes a built-in phase coupler to distribute power line communication signals across phases. An external phase coupler is not needed when the Q Relay is installed. The Q Relay physically isolates the IQ Series Microinverters from the grid when abnormalities are sensed or as required by grid regulations, and it automatically reconnects when valid grid conditions resume. The 4-pole Q Relay isolates all phase and neutral lines and works together with the Enphase Envoy-S gateway.

Enphase Relay controller, Single Phase - Rubicon Partner portal


Easy to Install

  • Lightweight and simple
  • DIN rail mount for quick installation 
    Align Relay clip into the bottom channel of the rail, then press in and up slightly until it clicks into place.

Reliable

  • Save on repairs and maintenance with incredibly low failure rates
  • Dependable load control
  • Automatically resets when normal voltage resumes

Smart

  • Can be configured to monitor 1, 2, or 3 phases
  • Remote upgrade capability
  • 25A rating allows more microinverters per AC circuit
  • Easy to read LEDs
  • Built-in power line communication phase coupler
Rubicon Sustainable Technology Applications

Enphase Relay controller is utilized in the following areas:

  • Residential
  • Small Commercial (0 - 50kW)
Enphase training

Enphase Training

This course teaches you all about Enphase microinverters. It will show you were the Enphase microinverters are connected, how they are connected to the Enphase module and to the DB board, and all the benefits of Enphase microinverters. It will also teach you all about how to access the Enphase module via Wifi and show you all the monitoring capabilities.

Learning Management System now available to all Rubicon eCommerce account holders

Complete this course to get points towards your Rubicon Glass score for Lead referrals.

EPR Badge - Rubicon Partner Portal

Regulators Compliance Certificated issued for the product by the NRCS in compliance with SANS 10142 Safety Regulations.

NRCS RCC - Rubicon Partner Portal

Regulators Compliance Certificated issued for the product by the NRCS in compliance with SANS 10142 Safety Regulations

Pollution degree: 2

Nominal input voltage (Vnom): 230 to 240 Vrms

Operating AC voltage range for power supply: 85 to 270 Vrms

Nominal input frequency: 50 Hz

Voltage and frequency acquisition time on
valid input during normal operation: 100 ms (5 line cycles @ 50Hz) 

Number of voltage inputs to monitor: 1

Number of Q Relays per system: Limit of four active Q Relay devices per system

Output: Two single pole, single throw contacts, normally open (L1 and N)

Output power rating: 4.8kVA

Output rating (typical): 230 to 240 Vrms, 20A

Power consumption: 10 VA

LEDs: Two red/green LEDs: one for under/over voltage trip, the other for under/over frequency and DCI

Mounting: 35 mm DIN rail (standard)

Width: 53 mm

Surge - L1 N output: Combination (1kV 2Ω)

Operating temperature range: -40 °C to 50 °C

IP rating: IP 20 (Must be used in a protected environment)

Relative humidity: 0 to 95 non-condensing

 

Enphase Relay controller, 1-phase, 20A
You have successfully subscribed!
This email has been registered